Wet felting a hat tutorial

While wandering through a local thrift store recently, I came upon a gigantic bag of wool!

I am the furthest thing from a wool expert, but I bought it based on the fact that it didn't smell, and someone put chestnuts in the bag. I heard once that chestnuts keep away moths and I figured that whoever owned this probably knew more about wool than me, and  therefore it must be worth buying. Certainly worthy of experimenting with.

It isn't all lovely smoothly combed out roving is it? I read a blog recently where a gal made a pair of wet felted slippers using raw wool and it looked like they worked quite well, so fingers crossed for this project.

First I weighed another felt hat that I have and it was around 85g. I want this one to be a bit smaller and the math to be a bit easier.

I weighed out 80g and then split that into 8 different piles of 10g each so I could make 4 layers of roving on each side of the resist.

I lay out my resist on top of a towel and a big sqaure of bubble wrap and started laying out my first layer:

The second layer looked a lot like dreadlocks and I was thinking that this might be a very Rasta sort of hat..(Make sure that each layer had the fibres going in a different direction than the one underneath).

Once I had my 4 layers set out, I covered the whole thing with a sheet of tulle and wet it down with hot soapy water. At this point you don't want a lot of suds, just a slippery surface.

This is a the handle of a drywall sander. Instead of sandpaper, I put in a piece of bubble wrap and rubbed the surface of the tulle. You can also just scrunch up a piece of bubble wrap and use that for friction,  but this way my hands stayed a bit dryer. Periodically peel up the tulle to make sure that the wool fibres aren't felting through too much. 

 You can see in the photo above that the wool around the perimeter of the resist is left dry. This is the part that will wrap around to the other side, so you don't want to felt it yet. Rub the wet surface for about 5 minutes or so. How long it takes can depend on the type of wool you are using. Merino top and Corriedale are quite good for wet felting. With this mystery wool though, I wasn't sure what to expect. When you think you might be getting close, you can do a pinch test: peel back the tulle and gently pinch the wet wool up. If it is still wispy, keep rubbing. If the layers are coming up together, you can flip it over and start on the other side..

I carefully folded over the overlapped edges and wet them down, before laying down the 4 layers on this side. I also made each layer hang over the edge of the resist to fold back onto the first side.

Once both sides were rubbed with bubble wrap and there was a good 'skin' on the wool (you've done some pinch tests), I covered the wool with hot sudsy water and put another layer of bubble wrap over top (bubbles facing in).

I rolled up into a tube and then rolled it back and forth  about 25 times, then unrolled it and rotated the hat clockwise 45 degrees, rolled it up and repeated. I did this 4 times, then flipped it over and repeated. 

I carefully cut the wool along the bottom of the hat and pulled out the resist. Then I sandwiched the hat between soapy hands and rubbed the the folded edge all the way around to make sure that it was felting as well as the flat parts. I the flipped the hat inside out and repeated the same rolling pattern as on the outside of the hat, sometimes getting the seams off center so it all felted evenly. I did want it to end up round after all. 

When I thought I might be working it down to the size I wanted, I wrung out the water and tried it on. I thought it was almost there, so I rinsed it in hot water, then cold, then soaked it for a couple of minutes in some cold water with a glug of vinegar in it to restore the proper pH. ( I was getting a bit tired and forgot to take pictures. It's not complicated though, and at this point your wool is pretty durable, so just rinse it out as you would a t-shirt). I rinsed out the vinegar water, wrung it out, and formed it over this very cool hat block that I just bought from here.

Now I have to wait for it to dry, and figure out how to embellish it a bit.

Making a hat block

Hat blocks, I have discovered, are not that easy to come by.  You can get them on Ebay or Etsy, but they are quite expensive.  I found one source here where they are quite reasonably priced especially if you live in the States. Shipping outside the US however, can start to add up.  Being impatient to get started, I decided to try and make my own.  I searched about the local thrift stores to find a hat that I could use as a mold, but I couldn't find any that I thought were sturdy enough. I dug through my own things and came up with a woven hemp cloche that I thought would do.

First, I lined the hat with plastic wrap to protect it from getting damaged. Then I filled it with this stuff:

It says on the can that it expands about 50% and it does, but slowly. I overfilled it of course but it was easy to carve back down to the shape I wanted.

I covered the whole thing in duct tape to protect the form and also to protect my wool from getting covered in little crumbs of foam.

I am really pleased with how it turned out. I am going to make a really tall dome next.

My first rug hooking project.

I found a really neat video of rug hooking on Youtube recently - using yarn!! It's the ultimate stash buster. I was eager to try it myself. I found a rug hooking kit for beginners here.  It took me about a week to do while watching tv in the evening and now it's complete!

 

I love it! Especially since it is a picture of sheep. I love sheep!